High Quality BDMA / CAS 103-83-3 / Benzyldimethylamine / N,N-dimthylbenzylamine

High Quality BDMA / CAS 103-83-3 / Benzyldimethylamine / N,N-dimthylbenzylamine

Overview:

Name: Dimethylbenzylamine

Alias: BDMA, N-dimethylbenzylbenzylamine, dimethylbenzylamine, benzyldimethylamine, catalyst BDMA, hard foam catalyst BDMA, N-benzyldimethylamine, BDMA, CAS 103-83-3, Dabco BDMA, Jeffcat BDMA, Lupragen N103, PC CAT NP60

Molecular formula: C9H13N;

Relative molecular mass: 135.20;

CAS No.: 103-83-3;

Colorless to slightly yellow transparent liquid, soluble in ethanol, soluble in hot water, slightly soluble in cold water;

Purity ≥99%;

Moisture ≤0.5%;

Viscosity (25℃): 90mPa.s;

Density (25℃): 0.897g/cm3;

Freezing point: -75℃;

Boiling range: 178-184°C;

Refractive index (25℃): 1.5011;

Flash point (TCC): 54°C;

Vapor pressure (20℃): 200Pa

Physical and Chemical Properties

Appearance Colorless to light yellow liquid.

Solubility Slightly soluble in cold water, soluble in hot water, miscible in alcohol, ether.

Melting point -75 °C

Boiling point 183-184 °C765 mm Hg(lit.)

Density 0.9 g/mL at 25 °C(lit.)

Refractive index n20/D1.501(lit.)

Flash point 130 °F

Storage conditions Flammables area

Water solubility 8 g/L (20 ºC)

BRN 1099620

Uses:

BDMA in the polyurethane industry is a catalyst for polyester-type polyurethane block soft foam, polyurethane rigid foam, polyurethane sheet and adhesive coatings, mainly used in rigid foam, can make polyurethane foam with good pre-fluidity and homogeneous vesicles, the foam body and the substrate between the adhesion of a better;

BDMA is mainly used in the field of organic synthesis as catalyst for synthesizing dehydrohalogen in organic drugs, corrosion inhibitor, acid neutralizer, accelerator for electron microscope section embedding;

BDMA is also used in the synthesis of quaternary ammonium salts, the production of cationic surface-active powerful bactericides and so on;

BDMA in epoxy resin, mainly used to promote the curing system of acid anhydride, polyamide, fatty amine, etc., to accelerate the curing of the product, widely used in epoxy resin electronic potting materials, encapsulation materials, epoxy floor coatings, marine paints as a curing accelerator;

Specific application examples of BDMA are: carbon fiber/monomolecular epoxy resin-based composite laminates, electrophoretic coatings for epoxy substrates, and dry transformer potting compounds;

Alias:

Dimethylbenzylamine Benzyldimethylamine BDMA 103-83-3 Dabco BDMA Jeffcat BDMA Lupragen N103 PC CAT NP60

Storage:

Should be sealed and stored in dry, cool and ventilated warehouse

Packaging:

200KG/drum Storage: it is recommended to store in dry and cool area with proper ventilation. Please fasten the package cover as soon as possible after the original packaging to prevent moisture and other substances from mixing and affecting the performance of the product. Do not inhale dust and avoid contact with skin and mucous membranes. Smoking, eating and drinking are prohibited in the workplace. After work, shower and change clothes. Store contaminated clothes separately and reuse them after washing. Maintain good hygiene practices.

Company Name:

Newtop Chemical Materials (Shanghai) Co., Ltd.

Sales Manager:

Hunter

E_Mail:

 sales@newtopchem.com

Telephone:

86-152 2121 6908

Fax:

86-021-5657 7830

Address:

Rm. 1104, No. 258, Songxing West Road,
Baoshan District, Shanghai, China (Mainland)

Website:

www.newtopchem.com

Benzyldimethylamine/N,N-dimthylbenzylamine

Benzyldimethylamine/N,N-dimthylbenzylamine

Overview:

Name: Dimethylbenzylamine

Alias: BDMA, N-dimethylbenzylbenzylamine, dimethylbenzylamine, benzyldimethylamine, catalyst BDMA, hard foam catalyst BDMA, N-benzyldimethylamine, BDMA, CAS 103-83-3, Dabco BDMA, Jeffcat BDMA, Lupragen N103, PC CAT NP60

Molecular formula: C9H13N;

Relative molecular mass: 135.20;

CAS No.: 103-83-3;

Colorless to slightly yellow transparent liquid, soluble in ethanol, soluble in hot water, slightly soluble in cold water;

Purity ≥99%;

Moisture ≤0.5%;

Viscosity (25℃): 90mPa.s;

Density (25℃): 0.897g/cm3;

Freezing point: -75℃;

Boiling range: 178-184°C;

Refractive index (25℃): 1.5011;

Flash point (TCC): 54°C;

Vapor pressure (20℃): 200Pa

Physical and Chemical Properties

Appearance Colorless to light yellow liquid.

Solubility Slightly soluble in cold water, soluble in hot water, miscible in alcohol, ether.

Melting point -75 °C

Boiling point 183-184 °C765 mm Hg(lit.)

Density 0.9 g/mL at 25 °C(lit.)

Refractive index n20/D1.501(lit.)

Flash point 130 °F

Storage conditions Flammables area

Water solubility 8 g/L (20 ºC)

BRN 1099620

Uses:

BDMA in the polyurethane industry is a catalyst for polyester-type polyurethane block soft foam, polyurethane rigid foam, polyurethane sheet and adhesive coatings, mainly used in rigid foam, can make polyurethane foam with good pre-fluidity and homogeneous vesicles, the foam body and the substrate between the adhesion of a better;

BDMA is mainly used in the field of organic synthesis as catalyst for synthesizing dehydrohalogen in organic drugs, corrosion inhibitor, acid neutralizer, accelerator for electron microscope section embedding;

BDMA is also used in the synthesis of quaternary ammonium salts, the production of cationic surface-active powerful bactericides and so on;

BDMA in epoxy resin, mainly used to promote the curing system of acid anhydride, polyamide, fatty amine, etc., to accelerate the curing of the product, widely used in epoxy resin electronic potting materials, encapsulation materials, epoxy floor coatings, marine paints as a curing accelerator;

Specific application examples of BDMA are: carbon fiber/monomolecular epoxy resin-based composite laminates, electrophoretic coatings for epoxy substrates, and dry transformer potting compounds;

Alias:

Dimethylbenzylamine Benzyldimethylamine BDMA 103-83-3 Dabco BDMA Jeffcat BDMA Lupragen N103 PC CAT NP60

Storage:

Should be sealed and stored in dry, cool and ventilated warehouse

Packaging:

200KG/drum Storage: it is recommended to store in dry and cool area with proper ventilation. Please fasten the package cover as soon as possible after the original packaging to prevent moisture and other substances from mixing and affecting the performance of the product. Do not inhale dust and avoid contact with skin and mucous membranes. Smoking, eating and drinking are prohibited in the workplace. After work, shower and change clothes. Store contaminated clothes separately and reuse them after washing. Maintain good hygiene practices.

Company Name:

Newtop Chemical Materials (Shanghai) Co., Ltd.

Sales Manager:

Hunter

E_Mail:

 sales@newtopchem.com

Telephone:

86-152 2121 6908

Fax:

86-021-5657 7830

Address:

Rm. 1104, No. 258, Songxing West Road,

Baoshan District, Shanghai, China (Mainland)

Website:

www.newtopchem.com

Dimethylbenzylamine CAS 103-83-3 N-dimthylbenzylamine

Dimethylbenzylamine CAS 103-83-3 N-dimthylbenzylamine

Dimethylbenzylamine CAS 103-83-3 N-dimthylbenzylamine

Dimethylbenzylamine CAS 103-83-3 N-dimthylbenzylamine

PU Catalyst: BDMA (benzyldimethylamine) CAS:103-83-3

Over view:

Common Name: Benzyl Dimethyl Amine

Other Chemical Names: N,N-Dimethylbenzylamine, Benzenemethamine, N,N-dimethyl-;Benzenemethanamine,N,N-dimethyl-;Benzylamine,

Physical and chemical properties:

Appearance

Form: transprant light yellow  liquid

Odour

no data available

PH

10 at 10 g/l at 20 °C

Melting point/freezing point

Melting point/range: -75 °C – lit.

Initial boiling point and boiling range

181 – 184 °C at 1.020 hPa – lit.

Flash point

53 °C – closed cup

Evaporation rate

no data available

Flammability (solid, gas)

Upper explosion limit: 6,3 %(V)

Upper/lower flammability

or explosive limits

Lower explosion limit: 0,9 %(V)

Relative density

0,9 g/cm3 at 25 °C

Water solubility

soluble

Partition coefficient: noctanol/water

log Pow: 1,87

Molar formular

C9H13N

Molar mass

135.21

1 (1)

Features and uses:

A liquid tertiary amine catalyst. Can improve foam cure and demolding time. It is an excellent candidate to consider for use in water-NCO reaction in rigid polyurethane foams.

BDMA is typically suitable to replace DMCHA in formulations using a high level of water as blowing or co-blowing agent can reduce surface friability and improve adhesion of foam to substrates.

BDMA promotes the urethane reaction and is commonly used in high-water rigid foam applications to reduce friability. It has a characteristic but low amine odor, and is soluble in water and in most organic solvents.

BDMA is used in flexible slabstock and rigid foam applications.

It promotes the urethane reaction and is commonly used in high-water rigid foam applications to reduce friability.

BDMA is also used for flexible slabstock foam applications.

Storage Information 

Recommends that our catalysts be stored in a dry and cool area under appropriate ventilation conditions. Each container should be closed tightly to avoid contamination with moisture or other negative influences that could change the products’ performance in the end use.

Package:

180KG/Steel Drum

(DABCO BDMA/Niax BDMA/ PC Cat NP60/ Addocat DB/ Jeffcat BDMA/ Lupragen N103)

BDMA / CAS 103-83-3 / Benzyldimethylamine / N,N-dimthylbenzylamine

Overview
Quick Details
CAS No.:
103-83-3
Other Names:
Benzyldimethylamine
MF:
C9H13N
EINECS No.:
C9H13N
Place of Origin:
Shanghai, China
Type:
Agrochemical Intermediates, Dyestuff Intermediates, Flavor & Fragrance Intermediates, Pharmaceutical Intermediates, Syntheses Material Intermediates
Purity:
≥99%
Brand Name:
NewTop
Model Number:
NewTop
Application:
Polyurethane Catalyst
Appearance:
Colorless
Supply Ability
Supply Ability:
1000 Ton/Tons per Month
Packaging & Delivery
Packaging Details
Drum,25 kg ,200L
Port
ShangHai
Picture Example:
package-img
BDMAMolecular formula: C9H13N;

Relative molecular mass: 135.20;

CAS number: 103-83-3;

Colorless to slightly yellow transparent liquid, soluble in ethanol, soluble in hot water, slightly soluble in cold water;

Purity ≥99%;

Moisture ≤ 0.5%;

Viscosity (25 ° C): 90 mPa.s;

Density (25 ° C): 0.897 g / cm 3;

Freezing point: -75 ° C;

Boiling range: 178-184 ° C;

Refractive index (25 ° C): 1.5011;

Flash point (TCC): 54 ° C;

Steam pressure (20 ° C): 200Pa
BDMA / CAS 103-83-3

One. The main use of BDMA

BDMA is a catalyst for polyester polyurethane block soft foam, polyurethane rigid foam, polyurethane sheet and adhesive coating in polyurethane industry. It is mainly used for hard foam, which can make polyurethane foam have good pre-flowability and uniform cells. Good adhesion between the foam and the substrate;

In the field of organic synthesis, BDMA is mainly used as a catalyst for synthesizing dehydrohalogen in organic drugs, a corrosion inhibitor, an acidic neutralizer, an accelerator for electron microscopy slicing, and the like;

BDMA is also used to synthesize quaternary ammonium salts to produce cationic surface active strong fungicides;

BDMA is mainly used to promote curing systems such as anhydrides, polyamides, and fatty amines, and accelerates product curing. It is widely used in epoxy resin electronic potting materials, encapsulating materials, epoxy floor coatings, and marine paints. Used as a curing accelerator;

Specific application examples of BDMA include: carbon fiber/single molecule epoxy resin matrix composite laminate, epoxy substrate electrophoretic coating, dry transformer potting;

Company Name:

Newtop Chemical Materials (Shanghai) Co., Ltd.

Sales Manager:

Hunter

E_Mail:

 sales@newtopchem.com

Telephone:

86-152 2121 6908

Fax:

86-021-5657 7830

Address:

Rm. 1104, No. 258, Songxing West Road,

Baoshan District, Shanghai, China (Mainland)

Website:

www.bdmaee.net

Website on alibaba:

pucatalyst.en.alibaba.com

PU Catalyst: BDMA (benzyldimethylamine) CAS:103-83-3

Over view:

Common Name: Benzyl Dimethyl Amine

Other Chemical Names: N,N-Dimethylbenzylamine, Benzenemethamine, N,N-dimethyl-;Benzenemethanamine,N,N-dimethyl-;Benzylamine,

Physical and chemical properties:

Appearance

Form: transprant light yellow  liquid

Odour

no data available

PH

10 at 10 g/l at 20 °C

Melting point/freezing point

Melting point/range: -75 °C – lit.

Initial boiling point and boiling range

181 – 184 °C at 1.020 hPa – lit.

Flash point

53 °C – closed cup

Evaporation rate

no data available

Flammability (solid, gas)

Upper explosion limit: 6,3 %(V)

Upper/lower flammability

or explosive limits

Lower explosion limit: 0,9 %(V)

Relative density

0,9 g/cm3 at 25 °C

Water solubility

soluble

Partition coefficient: noctanol/water

log Pow: 1,87

Molar formular

C9H13N

Molar mass

135.21

1 (8)

Features and uses:

A liquid tertiary amine catalyst. Can improve foam cure and demolding time. It is an excellent candidate to consider for use in water-NCO reaction in rigid polyurethane foams.

BDMA is typically suitable to replace DMCHA in formulations using a high level of water as blowing or co-blowing agent can reduce surface friability and improve adhesion of foam to substrates.

BDMA promotes the urethane reaction and is commonly used in high-water rigid foam applications to reduce friability. It has a characteristic but low amine odor, and is soluble in water and in most organic solvents.

BDMA is used in flexible slabstock and rigid foam applications.

It promotes the urethane reaction and is commonly used in high-water rigid foam applications to reduce friability.

BDMA is also used for flexible slabstock foam applications.

Storage Information 

Recommends that our catalysts be stored in a dry and cool area under appropriate ventilation conditions. Each container should be closed tightly to avoid contamination with moisture or other negative influences that could change the products’ performance in the end use.

Package:

180KG/Steel Drum

(DABCO BDMA/Niax BDMA/ PC Cat NP60/ Addocat DB/ Jeffcat BDMA/ Lupragen N103)

BDMAEE:Bis (2-Dimethylaminoethyl) Ether

CAS NO:3033-62-3

China supplier

For more information, please contact the following email:

Email:sales@newtopchem.com

Email:service@newtopchem.com

Email:technical@newtopchem.com

BDMAEE Manufacture !